![]() ![]()
When first turned on, though, the XTouch does not reflect the state of the XR. The encoder LED rings and mute LEDs follow the XR state when controlled by both the MIDI board and the normal network UI. Using the XTouch Editor, I have programmed eight encoders and eight buttons to control the faders and mutes for the critical channels and buses using the published MIDI messages. The converter and controller only draw about 100mA so I can run it for over twelve hours from a 2000mAh phone powerbank if there is no convenient power outlet or spare USB-A port. These two boards are mounted in a small box along with a connector for 5Vdc power. XTOUCH MINI OSCULATOR TO ATEM MIDI TEMPLATE PLUSI took the low-cost route by using HobbyTronics USB Host Mini (preloaded with MIDI firmware) plus a HobbyTronics MIDI Breakout. The HobbyTronics MIDI USB-DIN Converter is much lower cost but looks a little fragile (*) so would need to be repackaged for life on the road. The Kenton MIDI USB Host would work but is rather expensive. This can be resolved, though, with a USB/DIN MIDI converter. The XTouch Mini, in common with most small and reasonably priced controllers, is a USB MIDI device and the XR12 requires DIN MIDI. I have achieved this using the XTouch Mini. I did want the controller to have feedback for mute states and fader levels. I have long thought it would be good to have basic control via MIDI in case I lost my normal user interface but I did not want a large and/or expensive controller. I carry a spare 7" tablet, backup access point and an OTG adaptor for wired Ethernet but I don't have much time for trouble-shooting. The only challenge with this job is that I get very little time for get-in and get-out so any problems in setting up could be disastrous. XTOUCH MINI OSCULATOR TO ATEM MIDI TEMPLATE FULLI confirmed that Audition does the bank change correctly (though it populates the Mini with the right 8 channels as it considers it a full MC control surface).Ģ0200905: Added BANK RIGHT and BANK LEFT commands to A, buttons 9-10ĬONTROL TYPE CHANNEL NO.I have a regular small sound job that I handle with an XR12 controlled from a 10" Android tablet running Mixing Station X Air Pro. ![]() The Mini transposes its notes up an octave, so I programmed it with A#1,B1 instead. Kyle with Behringer support kindly pointed out the Bank Left and Bank Right commands (A#2,B2). I recently purchased the X-Touch Extender. XTOUCH MINI OSCULATOR TO ATEM MIDI TEMPLATE PROSet Audition and Premiere Pro to use Mackie Control (MC), but leave your device in MIDI mode. Manually enter these settings using X-Touch Editor. MIDI Map for Adobe Audition and Premiere Pro TURN EN 8 CC 1 CC23 Relative3 - PAN PAN TRACK 8 TURN EN 7 CC 1 CC22 Relative3 - PAN PAN TRACK 7 TURN EN 6 CC 1 CC21 Relative3 - PAN PAN TRACK 6 TURN EN 5 CC 1 CC20 Relative3 - PAN PAN TRACK 5 TURN EN 4 CC 1 CC19 Relative3 - PAN PAN TRACK 4 TURN EN 3 CC 1 CC18 Relative3 - PAN PAN TRACK 3 TURN EN 2 CC 1 CC17 Relative3 - PAN PAN TRACK 2 TURN EN 1 CC 1 CC16 Relative3 - PAN PAN TRACK 1 PUSH EN 8 NOTE 1 D#1 - MOMENTARY SELECT TRACK 8īT 1 NOTE 1 G#-2 - MOMENTARY SOLO TRACK 1īT 2 NOTE 1 A-2 - MOMENTARY SOLO TRACK 2īT 3 NOTE 1 A#-2 - MOMENTARY SOLO TRACK 3īT 4 NOTE 1 B-2 - MOMENTARY SOLO TRACK 4īT 5 NOTE 1 C-1 - MOMENTARY SOLO TRACK 5īT 6 NOTE 1 C#-1 - MOMENTARY SOLO TRACK 6īT 7 NOTE 1 D-1 - MOMENTARY SOLO TRACK 7īT 8 NOTE 1 D#-1 - MOMENTARY SOLO TRACK 8 PUSH EN 7 NOTE 1 D1 - MOMENTARY SELECT TRACK 7 PUSH EN 6 NOTE 1 C#1 - MOMENTARY SELECT TRACK 6 PUSH EN 5 NOTE 1 C1 - MOMENTARY SELECT TRACK 5 PUSH EN 4 NOTE 1 B0 - MOMENTARY SELECT TRACK 4 PUSH EN 3 NOTE 1 A#0 - MOMENTARY SELECT TRACK 3 PUSH EN 2 NOTE 1 A0 - MOMENTARY SELECT TRACK 2 PUSH EN 1 NOTE 1 G#0 - MOMENTARY SELECT TRACK 1 Also, I haven't tested the F1-8 functions yet hopefully they will work.ĬONTROL TYPE CHANNEL NO. One challenge that I ran into was that Premier Pro (and presumably Audition) did not recognize many of the valid commands such as Solo, so I only had a few that I could map. I used a couple of Mackie Control/MIDI tables that I found online, and also used the MIDI Monitor window in Presonus Studio One to view the commands from the board while it was in MC mode. XTOUCH MINI OSCULATOR TO ATEM MIDI TEMPLATE SOFTWAREApply the settings using the X-Touch Editor software (download from ). XTOUCH MINI OSCULATOR TO ATEM MIDI TEMPLATE DOWNLOADYou'll want to copy this into a text editor so that the tabs will render correctly (or download the attached text file). In case it helps someone save time figuring it all out, here's my MIDI map for the Behringer X-Touch Mini. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |